Reasons Your fiat 500 new key 500 Key Fob Won't Work

A key fob for the fiat 500 how to open boot without key 500 makes it easy to open doors and start your car. There are a myriad of reasons the key fob might stop working. This includes a dead battery water damage, issues with the receiver module, and interference.

This listing is for an NEW replacement fiat remote key Flip Key Remote - an exact replica of the Ilco brand that must be programmed professionally by a local locksmith (click here to search for a Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common reason for your 500 key fob being inoperative. Modern key fobs have a very limited operating range and must be within a few feet of the vehicle to operate. If you're far from your vehicle and press the key fob button, the car won't be able to respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a brand new one of a reputable brand like Panasonic Duracell or Energizer. You can find them at your local hardware store or online.

You can test the coin-cell battery by pressing the buttons while you are standing close to your fiat ducato replacement key 500. The car should blink its parking lights and the key fob should be able to operate the lock and unlock switches.

If your key fob isn't working even after replacing the battery, it might be water damage that has prevented it from connecting to the module inside your vehicle. Water damage can occur through a variety of methods, including an easy splash or submerging the key fob saltwater at the beach. If you suspect your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If this does not work, you'll have to get your fob reprogrammed either by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean or wash it in a machine. Saltwater can cause the circuit board to short and eventually fail. Getting the fob wet is not a good idea however, if you drop it into the water in a cup or forget to take it out of your pants pocket prior to running the washer and you don't have a chance, don't give in.

First remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl or similar products. Then check the fob to see if it works. If the key does not function then it might need to be changed. This is typically handled by a dealer or professional auto locksmith.

If the key is older and hasn't been programmed to your car It is likely that it needs to be replaced completely. This is an easy process that can be completed by a professional automotive locksmith. The locksmith will have to cut the key to match the ignition in your vehicle. They'll also have to reprogram the fob in your car's system. It's a simple and inexpensive process that can be completed the next day.

Receiver Module Issues

One of the main reasons your 500 key fob may stop working is because it's out of range. The remote usually has an area of 30 feet or less, and if it's too far away from your car it won't respond to your commands. This can be easily fixed by moving it closer to your vehicle until it starts responding.

If you've replaced the coin battery (commonly known as a "button" or "watch") and the fob isn't working It could be because of an internal circuit board issue. In most cases, reprogramming the fob will fix the problem. You can find the instructions for the majority of vehicles on YouTube or in the owner's manual.

It's possible that you need to replace the metal clips that keep the battery of your coin in place. If they loose tension, it can prevent the coin battery from sitting properly, and this will cause the fiat panda remote key replacement to malfunction.

In rare cases the fob may be out of connection with your vehicle as a result of hardware or software problems. This could be a huge headache, but you can usually fix it by visiting an auto locksmith to have them reprogram your fob for you. In some instances it may be necessary to reinstall the program in your body control module as well.

Interference

In addition to a dead battery on a coin The key fob might not be able to transmit or receive an signal due to interference. This could occur if the key fob is located near radio transmitters (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob might not function could be due to a weak connection to the buttons, damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or if you've tried everything at home to fix it (e.g. replacing the battery, reprogramming it and using the spare key fob, you could have a faulty receiver module on your 500. The receiver module, located beneath the dashboard, receives radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then processed by the vehicle.

Luckily, there is an easy way to reset all on-board systems in your 500 and include the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will remove any residual electricity and restart the car's computer system, which can help get your key fob working again. If the problem persists it is recommended that you consult an experienced technician. They will be able to identify the exact cause of problems.