Reasons Your fiat key replacement cost fiat 500 key fob not working Key Fob Won't Work

A key fob from fiat Ducato key fob 500 makes it easy to open doors and start your car. There are many reasons the key fob might stop working. It could be due to a dead battery or water damage, receiver module issues, and interfering.

This listing is for an NEW replacement fiat panda remote key replacement Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason the 500 key fob won't work is a dead battery. Modern key fobs have a very restricted operating range, and must be within a few feet of the vehicle to function. If you're far from your vehicle when you press the key fob button, the car won't respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery on your coin cell (Part number CR2032) with a new one from a reputable manufacturer like Panasonic, Duracell, or Energizer. You can find them at your local hardware store or on the internet.

After you've replaced the battery in the coin cell you can test it by standing near your fiat ducato remote key replacement 500 and pressing the buttons. The car will blink its parking lights, and the key fob will operate the lock and unlock buttons.

If your fob's fiat abarth key isn't working even after replacing the battery, it might be water damage that is preventing it from connecting to the module in your vehicle. Water damage can happen in a number of ways, from the slightest splash to submerging your fob in salt water at the beach. If you suspect that your fob was exposed to water, place it in a rice bag to draw out the moisture. If this doesn't work, you will need to have your fob replaced by an auto locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean or wash it in a washer. Saltwater poses a particular risk to the circuit board of the fob that can cause it to short out and eventually die. In the event that you let your fob get wet, it's not an option but if you drop it in a cup of water or forget to take it out of your pants pocket before running the washing machine Don't give up hope.

Take the battery off first. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Test the fob next to verify if it's functioning. If the fob doesn't work, it may have to be changed. This is usually handled by a professional or dealer auto locksmith.

If your key is older and not programmed to work with your vehicle then you'll need to replace it completely. A professional locksmith in the automotive industry can complete this simple process. The locksmith will need to cut the key to match the ignition on your vehicle. They will also need to reprogram the fob in the car's system. This is a cheap and fast process that can be completed within the same day.

Receiver Module Issues

The 500 key fob you have may stop working because it is out of range. The remote typically has an area of 30 feet or less, and if it's too far from your vehicle, it will not respond to your commands. It can be solved by moving it closer to your vehicle until it begins responding.

If your fob does not work after you replace the battery for the coin, also known as a "button", "watch" or "button", it could be due to an issue with the circuit board inside. Reprogramming the fob typically resolves the issue. You can find the procedure for the majority of vehicles on YouTube or in the owner's manual.

It is possible to replace the clips made of metal that hold the coin batteries in the correct position. If they loose tension, it may prevent your battery from sitting properly and cause your remote to malfunction.

In rare instances the fob might become desync'd with your vehicle due to software issues or hardware issues. This can cause a major trouble, but you could usually resolve this issue by visiting an auto locksmith to have them reprogram your fob. In some instances they might need to reinstall the software in your body control module too.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This is possible when the key fob is near the radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. The key fob might not function due to a bad connection with the buttons or water damage, or damage to the internal chips.

If the key fob has been unable to function for a while without notice or after trying everything you can do at home to fix it e.g. replacing the battery, reprogramming it and using the spare key fob, you might have a damaged receiver module on your 500. The receiver module, located under the dashboard, picks up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Luckily, there is an easy method to reset every single system on board in your 500 device, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then, reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the car's computer. This will help you get your key fob to work again. If the issue continues it is recommended that you consult an experienced technician. They will be able diagnose the root of any issues.