Reasons Your Fiat Panda Key Fob Replacement 500 Key Fob Won't Work

A key fob for Fiat 500 makes it simple to open doors and start your car. However, there are numerous reasons why the fob may stop working. This includes a dead coin-battery water damage, receiver modules issues, and interference.

This listing is for an NEW replacement fiat panda key programming Flip Key Remote - an exact replica of the Ilco brand that must be professionally programmed by a local locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not working. Modern key fobs come with a restricted operating range, and should be within a few feet of the vehicle to operate. If you are not within your vehicle and press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) with a new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can typically find them in your local hardware store or online.

After you've replaced the battery of your coin cell, you can test it by standing next to your fiat doblo key fob replacement 500 and pressing the buttons. The car should blink its parking lights, and the key fob should operate the lock and unlock buttons.

If the key fob doesn't work after replacing the battery, it could be damaged by water that blocks it from communicating with the receiver module in your vehicle. Water damage can occur in a variety of ways, ranging from a light splash to submerging your fob in salt water at the beach. If you believe your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If this fails, you'll need to have your fob reset by an auto locksmith or dealer.

Water Damage

Water damage can occur when you immerse the fob in the ocean or wash it in a washer. Saltwater is especially dangerous to the fob's circuit board, causing it to short out and eventually die. If you get the fob wet, it's not an ideal choice however, if you drop it into a glass of water or don't remember to take it out of your pocket before you run the washing machine, don't give up hope.

First take the battery off the fob. Clean the electronic chip with isopropyl or a similar product and then dry it thoroughly before replacing the battery. Check the fob again to determine if it's functioning. If the fob doesn't work then it might need to be changed. This is usually handled by an auto locksmith or dealer.

If the key is older and has never been programmed to your car it is likely to need to be replaced completely. This is a straightforward process which can be accomplished by a professional automotive locksmith. The locksmith will need the key to be cut to match the car's ignition. The locksmith also needs to reprogram the fob into the vehicle's system. This is a fast and inexpensive process that can be completed the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob may stop working is that it's simply out of range. The remote has a range of 30 feet, which means should you be too far away from your vehicle it will not respond to your commands. You can easily solve this issue by moving the remote closer to your vehicle until it responds.

If you've replaced the coin battery (commonly known as"button" or "button" or "watch") and your fob doesn't function, it could have an internal circuit board issue. In the majority of cases, reprogramming your fob will resolve this issue. You can find the steps for the majority of vehicles on YouTube or in the owner's guide.

It may be necessary to replace the metal clips that hold the coin batteries in place. If they loose tension, it can prevent the battery from being properly seated and result in the malfunction of your remote.

In rare instances, the fob can become out of the vehicle's sync because of hardware or software problems. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances it may be necessary to reinstall the software on your body control module, too.

Interference

Interference can also cause the key fob to not receive or transmit an signal. This could occur if the keyfob is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons why the key fob might not function could be due to a weak connection to the buttons or damage to the internal chip or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. replacing the battery, reprogramming it and using the spare key fob, you may have a defective receiver module on your 500. The receiver module is situated under the dash and picks up the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

There is a straightforward method to reset the 500's onboard system including the keyfob. Disconnect the battery of 12 volts for about 15 minutes, by removing the negative cable and then the positive cable. Reconnect the battery. This will remove any remaining electricity and restart the car's computer system, which could allow you to the key fob to function again. If the problem persists it is recommended that you consult an expert technician. They can determine the exact cause of your issues.