How to Replace subaru key fob to Change a Subaru Spare Key

If you've lost your Subaru car key, call a locksmith. Usually, they will cut an alternative key for you at a lower cost than the dealer.

Fob remote "push to start" intelligent keys or a plain metal key are the two most common kinds of Subaru car keys. The Fob key needs to have its chip reprogrammed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. These remotes function with keys inside your car to connect to the computer system of your vehicle.

Subaru models offer a little known feature called PIN Code Access. You can make a custom number sequence to start and open your car. Refer to the owner's manual for learn how to program subaru key fob to utilize this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

If your keys stop working, there's an excellent chance that the battery in the key fob is dying. You can check the battery life of your key fob by using a portable tester or a multimeter in your garage.

The next step is to remove the circuit board of the transmitter from the key fob and examine it. The board will contain one or two sets of eight-digit numbers, so write down the first set so you will be able to remember it later. After you've completed this, you can begin programming your key fob at home. The procedure to do this is different based on the model and year of your vehicle, but it's usually simple enough to complete yourself.

Key Fobs

subaru lost key fob's newest models feature key fobs which not only unlock doors but also switch on lights, lock gas cap and even start the car. This last trick is particularly useful if you've encountered yourself at a gas station and your car won't even start because the battery inside the key fob has failed.

It's likely that your Subaru's key fob, whether it's old or new can be replaced easily. Be aware that some modern models, with their high level technology, might require a visit to the dealer. However, with a little time and effort, you can have your replacement key fob waiting to be used at home.

Begin by looking at the circuit board of the transmitter in your key fob (instructions to open the case must be included in the owner's manual). It should have one or two sets of serial numbers each of which is 8 digits long. Keep the first series of numbers on hand for future information.

Then, sit in your driver's seat, and close all the doors. Turn the key ten times to start your car, then switch off the engine. Press the lock button on your key fob, and then open the door. This will confirm whether your doors work correctly. After that close the door, and remove the key from the ignition. You should hear your vehicle sound again, signalling that the key fob has been programmed.

Ignition System

The battery for the key could be dead if your Subaru keys aren't functioning as they should. You can replace the battery for your key fob at home if you are familiar with the procedure. A replacement battery is not expensive and relatively easy to locate. If your keypad doesn't respond to your commands, there could be a different issue. To get a spare key, it's recommended to go to an authorized dealer. They will make sure that the key is genuine Subaru key, that is in warranty, and is programmed to your vehicle. This is a lot simpler and safer than getting an aftermarket one from a company online.

You can also request that the dealer cut a brand new key if you provide them with your VIN number and evidence of ownership. They'll use this information to program the new key to ensure that it will be recognized by your immobilizer. This is a much more complicated procedure than cutting a key, and the dealership will charge you more for it.

Once the new key is programmed, it is possible to switch it over to the working key. It will take only five seconds to insert the new key, so make sure to keep your working key at the ready. You can remove the key after the security light been off and you've tested it.

Battery Replacement

Subaru fobs are very beneficial because they can switch on the sunroof and power windows in your car with just one button press. The battery in your Subaru fob isn't built to last forever, and it will require replacement at some point. It's good news that replacing the battery is a straightforward procedure that you can carry out yourself with the help of this quick guide from Capitol Subaru.

To begin you'll need to locate the small crevice within the seam that separates the front and back of your key fob. You can then open the seam with a flathead screwdriver to reveal the small compartment that houses the battery. Remove the old battery and then insert a new one, ensuring that it is facing the correct side up. After you have put everything together you can use the new key fob to lock in, unlocking, and even starting your vehicle.

Always have a spare set keys, particularly if the one you have is broken or has been lost. A new key can be found at your local auto dealer or you can get one made by locksmiths. It's crucial to get your key fob functioning properly in the shortest time possible to ensure you drive in a safe manner!