How to Replace a Kia Sportage Replacement Key

For many Kia models the key comes with a keyless entry system built-in. The key functions like remote controls, and can be exchanged with a Kia dealer.

Key fobs might stop working due to a variety of reasons, including an empty coin battery worn buttons, water damage, signal interference and a damaged receiver module. Here are some helpful tips on how you can get your Kia Sportage replacement key to function again.

How to replace the remote key or smartkey?

The battery in your Kia's intelligent key will eventually need be replaced, regardless of whether it's a remote, a push-to-start key or a regular metal key that doesn't have an electronic transponder. This is particularly relevant if your vehicle displays a message indicating that the remote or smart keys are in poor condition.

Luckily, this is an easy procedure. To replace the battery on the key fob remove the mechanical key from the slit at the back of the key fob. You then need to pry open the cover. A small screw will be found inside the key fob to keep the battery in the correct position. Take out the old battery by detaching the screw with a small screwdriver. Then insert the new one and close the slit inside the key fob for kia fob.

Once the key fob has new batteries, test it by pressing the lock and unlock buttons. If the doors lock and unlock in the same way, you're good to go! You can now take advantage of your Kia's hands-free lock/unlock feature whenever your fingers feel cold or you need to make errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a machine for programming that is only available to the automotive locksmith or dealer. Other keys (non-transponder metal keys) don't require programming. If your key needs to be programmed again, you will need to be aware of the number written on the tag of the key code and record it in a safe location.

how to get a new kia key fob do I replace the battery?

If the kia key replacement near me key fob does not respond to pressing the lock or unlock button, it is likely that the battery is not fully charged. A battery that is not functioning properly could cause other issues such as the check engine light flashing on or delayed engine cranking. It is fairly easy to replace the key fob batteries with only a few simple tools.

Make sure to shut off your vehicle and close all doors prior to beginning. Find the small metal or a plastic piece on the bottom of the key fob. Press it until the key pops out. This key can be placed inside the driver door handle to unlock your car.

To replace the battery in the key fob remove the cover at the rear. Utilize a plastic plier tool to remove the latch that holds the black negative cable. Take the old battery out, and then orient the replacement battery to ensure its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid bending or damaging the contacts on the metal.

After the new battery has been installed, turn the key fob off and then on in the ignition repeatedly until the door locks cycle. Then, you can test your kia ceed key replacement car key cover (kingranks.com) key fob to check whether it's working again.

How can you replace the smart key?

There is a possibility of having a standard keyfob or a Smart Key depending on the model of Kia Sportage. The smart key features an embedded mechanical key blade, however, the standard key fob does not. Both types of key fobs are equipped with batteries inside which eventually needs to be replaced. Fortunately, it's an easy process that only takes about two minutes.

Before you start it is essential to make sure that you are on a level surface with sufficient lighting and that the Kia is off. Keep in mind that there are tiny parts inside the fob that could fall out if not vigilant.

The release button for the small size is located on the lower backside. This will either be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been opened, take out the battery that was in it. The new battery is a CR-2032, and can be bought through the internet or at a local auto parts shop. After you've finished it should be possible to lock and unlock your vehicle with your key fob, even if your engine isn't running!

How do you replace a broken mechanical key

The 2012 kia rio key fob programming key fob is a wonderful convenience that allows us to lock and unlock our vehicle with the push of the button. However, like all devices it may have issues occasionally. There are methods to troubleshoot these issues and keep our key fobs in good working condition for the long term.

One of the most common problems is a weak or dead battery. This can cause your fob to stop working or work intermittently. If this is the issue, replace the battery with an entirely new battery.

If this isn't enough to solve the issue, use an ordinary screwdriver with a flat head to push the fob's casing made of plastic open. Be careful not damage any internal components or scratch the plastic. When the battery is open, carefully take off the old battery and replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to confirm it's working properly. Contact a dealer, or a locksmith to resolve the problem if the fob is still not working. To avoid lockouts in the future, ensure you have an emergency key that will be able to work with all trunk and door cylinders.