Replace Nissan Key Fob Batteries

If your nissan hardbody key keyfob isn't responding to your commands, its battery may be dead. Fortunately, this is a relatively easy repair that most people can do themselves.

You can purchase a replacement nissan key from a hardware store or from your owner's guide for the specific model you have, and you'll need to follow these steps to replace the battery.

Changing the Battery

The key fob on your Nissan model has a built-in battery that could eventually lose its charge. The battery in the key fob can be changed in just a few minutes. First, you'll need the CR2032 batteries. It's a tiny coin-cell battery that is used in the majority of key fobs. You can buy it in a majority of convenience stores. You will also need gloves (latex or non-latex) and a small screwdriver with a flat head to open the fob. Before starting, be sure to consult the owner's manual to find specific instructions and steps.

After you have the new battery, take off the old one by turning the fob on its side and looking at the backside. There is a tiny catch that you have to release by pulling it downwards. This will remove the mechanical key from the original position inside the fob.

Next, insert the new battery and make sure that it is oriented correctly. Close the fob after the battery is installed and click the two sides of the fob together. After you have completed this step check your key fob by pressing the unlock button and watching what happens. You'll be able to use the many functions of your Nissan If everything is working correctly. It's also a good idea to program the key fob after replacing the battery to make sure it's operating properly.

Replacing the Transmitter

Your key fob serves as the "key" to so many of your car's essential functions, it could be a huge loss should you lose or break it. A damaged or dead key fob could prevent you from locking and starting your car.

It's a good idea to have a spare key fob around in case of an emergency. Fortunately, the process for replacing your nissan micra key programming key fob is fairly easy. The procedure for replacing your nissan car Key case key fob is fairly simple. You will need a new flathead screwdriver and an entirely new battery to replace the old.

You'll also require an Panasonic CR2032 3V round battery (you can find them in multipacks that cost under $5 USD). The battery is in the back part of the key fob. You'll require a small flathead screwdriver to gently separate the two halves. Make use of a flathead screwdriver or a small flathead to take off the clip that is on top of the battery. Make sure you note the position. Replace the battery and put the key fob back together. You can test it to make sure it works properly.

As with any electronic device that you own, your Nissan Intelligent Key will eventually wear out due to regular use and will require replaced. Protect your key fob against water, magnetic fields and physical impacts. Don't drop it or apply too much pressure to the device.

Replace the Key

When your Nissan key fob has gone out and you're unable to use it to unlock or start your vehicle. This is a problem for those who need to get to work in Detroit, run errands near Dearborn or spend an evening out close to Troy.

It's not too difficult to change the battery in your Nissan Smart Key. You can do it at home or at a dealership, and usually, you can find a set for less than $5 at a hardware store.

Start by flipping the fob upside down and pushing a small catch on the back. This will open the emergency key that is mechanical. The emergency key won't allow you to start your car however it will open the door.

Look for a small slit at the top of the casing. You can use a screwdriver or a plier to break out the two pieces of the key fob. Once you've got access to the battery within, pull it out and note of its position. When you're ready to put back together the key fobs, slide the new battery into its place and then snap the two pieces of the case. Insert the mechanical key and your Nissan smartkey will function as normal.

Other Issues

A lot of modern cars come with key fobs which allow you to lock and open them without having an actual car key. The key fob is equipped with an electronic transmitter to connect with the computer system in the car.

If your Nissan key fob does not function after you replace the battery, there could be several reasons for this. For one, the new battery may not be properly seated in the key fob. Resetting the key fob is also a possibility. This is a simple procedure that you can do at home using just a few simple tools.

You'll need, for example a screwdriver that has a flat-headed tip to remove the battery that was in the key fob. Then, using a screwdriver, pull the back of the keyfob and then insert the new batteries. Then, you'll need reset the key fob so that it is compatible with your vehicle.

You can easily program your Nissan key fob by yourself, because they all have the ability to be programmed by you. It is usually done by inserting the key fob into the ignition twice within five minutes. If this doesn't work, you can take your key fob into an auto locksmith to have it programmed. The cost of this will depend on the person you call and the type of car you own.